Quck answer
To install a double-action hinge, follow these steps:
1. Measure and mark the desired location for the hinge on the door and the frame.
2. Use a chisel to create recesses for the hinge plates on both the door and the frame.
3. Position the hinge plates in the recesses and mark the screw holes.
4. Pre-drill holes for the screws using a drill bit that matches the screw size.
5. Attach the hinge plates to the door and the frame using screws.
6. Test the hinge by opening and closing the door to ensure smooth operation.
7. Adjust the tension of the hinge if needed using the adjustment screws.
8. Secure any additional screws or fasteners provided with the hinge.
Remember to refer to the manufacturer’s instructions for specific guidelines on installing the double-action hinge.
Double-action hinges are hinges that allow a door to swing open in either direction, while internal springs pull the door closed automatically. These hinges are usually surface-mounted to a wooden door frame or finished opening. Some hinges can be recessed or flush-mounted. For specific installation instructions, refer to the manufacturer’s literature.
Most double-swinging doors require two hinges, but larger doors may require three. It is usually easiest to install the hinges onto the door before mounting the door to the frame or opening.
Preparing for Installation
Before you begin the installation, ensure that you have a drill with the appropriate size of drill bit to predrill where the screws will be driven. A screwdriver bit that fits the head of the screws, a tape measure, a pencil, and a level will all be necessary for proper mounting as well. Each door will need at least two double-barrel action hinges, one mounted on the top of the door and one mounted on the bottom. If a third hinge is required, it will be centered between the other hinges.
These double-action hinges operate due to tension pins nestled in the barrels of the hinges. These pins must be removed before installing the hinges to the door. To do this, take the tension rod provided, insert it into one of the holes found on the barrel, and rotate away from the hinge. Remove the pin and set it in a safe spot where it won’t be lost.
Necessary Materials
-
Cardboard
-
Tape measure
-
Pencil
-
Level
-
Drill
-
Drill bit
-
Screwdriver bit
How to Put in a Double-Action Hinge
Step 1: Mark the Location of the Upper Hinge
Measure 3 inches from the top of the door and mark this distance with a pencil. Find the center of the door’s edge (front to back) and mark this in two places. Use a level and a pencil to draw a line through the center marks, starting at the 3-inch mark and extending several inches down. Place the hinge on the door so the top of the barrel is on the 3-inch mark and the center line runs through the centers of the top and bottom hinge holes. Mark the hinge holes with the pencil.
Step 2: Mount the Upper Hinge to the Door
Drill a pilot hole in the center of each hinge hole location using a drill and a bit sized for the mounting screws. Position the hinge and fasten it to the door with the screws provided. Follow the manufacturer’s instructions for orienting the hinges. The orientation and position of each hinge may vary based on where the hinge is installed.
Step 3: Install the Lower Hinge
Mark, predrill, and install the lower hinge using the same process used for the upper hinge but place the lower hinge so its bottom edge is 7 inches from the bottom of the door. If you’re installing two doors, repeat that same process to mount the hinges to the second door.
Fourth Step: Indicate Hinge Placement on the Door Frame
Measure the midpoint of the door frame’s top and bottom openings, and create a straight line with a pencil and level. Hold the door up to the frame and ensure the hinges align with the center line. Balance the door evenly between the frame’s top and bottom and mark the hinge mounting holes using a pencil. Set the door aside.
Fifth Step: Install the Door(s)
Drill pilot holes for the hinges, reposition the door, and secure it with the provided screws. Reinsert the tension pins into the hinge lugs. Repeat the process for the second door, if applicable. Verify the space between the doors when closed. If needed, add flat cardboard shims behind one or more hinges to ensure an even door gap.
Sixth Step: Adjust the Hinge Tension
To adjust hinge tension, use the tension pin and insert it into one of the holes, rotating it towards the door jamb. Insert the pin once the appropriate tension has been reached. If the door seems to be moving too slowly, more tension needs to be applied to the hinge. The correct tension is achieved when the door swings back into place at a reasonable pace. Do not exceed five tension holes on the top.
FAQ
1. What is a double-action hinge?
A double-action hinge is a type of hinge that allows a door or gate to swing open and close in both directions. It is commonly used in commercial settings, such as restaurants, where doors need to swing open in both directions for easy access.
2. What tools do I need to install a double-action hinge?
To install a double-action hinge, you will need a few basic tools, including a power drill, a screwdriver, a tape measure, a pencil, and screws that are appropriate for the material you are mounting the hinge on.
3. How do I measure and mark the placement for the double-action hinge?
To measure and mark the placement for the double-action hinge, hold the hinge against the edge of the door or gate, making sure it is centered. Use a tape measure to measure the distance from the top and bottom of the door or gate to the top and bottom of the hinge. Mark these measurements with a pencil.
4. How do I install the double-action hinge on the door or gate?
To install the double-action hinge on the door or gate, position the hinge against the marked placement. Use a power drill to pre-drill pilot holes for the screws. Then, secure the hinge to the door or gate using the appropriate screws and a screwdriver.
5. How do I install the double-action hinge on the door frame?
To install the double-action hinge on the door frame, hold the door in place and mark the placement of the hinge on the frame. Use a power drill to pre-drill pilot holes for the screws. Then, secure the hinge to the door frame using the appropriate screws and a screwdriver.
6. How do I adjust the tension of the double-action hinge?
To adjust the tension of the double-action hinge, locate the tension adjustment screw on the hinge. Use a screwdriver to tighten or loosen the screw, depending on whether you want to increase or decrease the tension. Test the door or gate to ensure it swings smoothly.
7. Can I install a double-action hinge on my own?
Yes, you can install a double-action hinge on your own if you have the necessary tools and basic DIY skills. However, if you are unsure or uncomfortable with the installation process, it is recommended to seek professional help to ensure proper installation and functionality of the hinge.