Quck answer
Taking apart a Maytag washer can be done in a few simple steps. First, make sure to unplug the washer from the power source. Next, remove any screws or fasteners holding the control panel in place, and gently lift the panel to expose the inner workings. Disconnect any wires attached to the control panel, taking note of their placement for reassembly. Next, remove the outer cabinet by removing any remaining screws or fasteners. Once the cabinet is removed, you will have access to the internal components of the washer. Remember to take caution and refer to the user manual if needed.
For effective repairs on your Maytag washer, it is necessary to disassemble the washer cabinet. This grants access to all the internal mechanisms for quick repairs and also enables you to test and troubleshoot the entire washer. The Maytag washer is held together by just a few fasteners.
Step 1
Disconnect the power cord of the Maytag washing machine from the wall and turn off the water at the wall spigots. Move the washer away from the rear wall and place a bucket underneath the water supply hoses at the back panel of the washer.
Step 2
Using channel lock pliers, loosen the water hose connections from the back of the washer. Remove the hoses from the washer and let the water drain into the bucket. Keep a towel nearby to wipe up any spills.
Step 3
Locate the three screws at the top rear edge of the control panel that hold it in place to the rear of the washer. Remove the screws using a Phillips screwdriver. Tilt the control console forward and detach the tabs on the bottom of the control console from the holes in the top of the washer.
Step 4
Use masking tape to label and wrap small pieces of tape around the wires connecting to the different components inside the control console. Detach the wires from each individual component by pulling the wire end from the component terminal. The temperature switch, pressure switch, speed switch and timer are all accessible inside the control console.
Step 5
Use a nut driver to remove the two screws holding the lower access panel to the front of the washer. The screws are located near the floor on the bottom edge of the access panel. Pull the access panel away from the washer. This gives access to the water pump, drive belt and drive motor of the washer.
Step 6
Locate the two screws holding the bottom of the front panel to the sides of the washer. Remove the screws using a nut driver. Swing the bottom of the front panel towards you and pull down to disengage the top of the front panel from the top panel.
Step 7
Cover the laundry lid on the top panel with masking tape. Use a nut driver to remove the two screws holding the top panel to the sides of the washer. Lift the front of the top panel up and back, raising it like a hood of a car. The top panel has two hinges on the rear edge that allow it to rest in a service position. Now, the remaining parts of the washer, including the tub, water inlet valves and drive assembly, are fully accessible.
FAQ
1. How do I prepare for taking apart a Maytag washer?
To prepare for taking apart a Maytag washer, start by gathering the necessary tools such as a screwdriver, pliers, and a socket wrench. Make sure to unplug the washer from the power source and turn off the water supply. Remove any clothing or items from the washer and empty the drum. It’s also a good idea to have a workspace with enough room to maneuver around the washer.
2. What is the first step in taking apart a Maytag washer?
The first step in taking apart a Maytag washer is to remove the control panel. This can usually be done by removing a few screws or releasing some clips. Once the control panel is removed, you can access the wiring and other components inside. Make sure to take note of how the wires are connected or take pictures for reference later.
3. How do I remove the top and front panels of a Maytag washer?
To remove the top panel of a Maytag washer, locate the screws or clips holding it in place and remove them. Lift the top panel up and set it aside. To remove the front panel, you may need to remove additional screws or clips near the bottom. Once these are removed, carefully lift the front panel up and away from the washer.
4. Can I take apart the drum of a Maytag washer?
Yes, you can take apart the drum of a Maytag washer. However, this is a more complex task and may require more advanced knowledge and tools. If you need to access the drum for repairs or cleaning, it’s recommended to consult the Maytag washer’s manual or seek professional assistance to ensure it is done correctly.
5. How do I put a Maytag washer back together after taking it apart?
To put a Maytag washer back together after taking it apart, simply reverse the steps you took to disassemble it. Make sure to reconnect any wires, screws, or clips that were removed. Pay attention to any specific instructions or diagrams in the manual. Once everything is reassembled, plug the washer back into the power source, turn on the water supply, and test it to ensure it is functioning properly.