Quck answer
An LG washer that stops at the rinse spin cycle can be troubleshooted and repaired by following these steps:
1. Check the power supply: Ensure that the washer is properly connected to a power source and that the circuit breaker hasn’t tripped.
2. Clean the drain hose: A clogged or kinked drain hose can cause the washer to stop. Remove any obstructions or straighten out any kinks in the hose.
3. Inspect the water inlet valve: The water inlet valve controls the flow of water into the washer. If it is faulty, it may need to be replaced.
4. Examine the motor control board: A malfunctioning motor control board can cause the washer to stop. Inspect it for any visible damage or signs of a burnt-out component.
5. Test the door lock switch: If the door lock switch is defective, the washer may not proceed to the rinse spin cycle. Use a multimeter to check for continuity and replace if necessary.
By following these troubleshooting steps, you can identify and repair the issue causing your LG washer to stop at the rinse spin cycle.
If your LG washer stops during the rinse and spin cycle, it’s likely due to water not draining properly from the machine. Since draining and spinning are interconnected, any issues with draining will affect spinning and vice versa. Clogging in the drain filter is a common problem in LG washers leading to draining issues, and resolving it will prevent the washer from stopping during the rinse and spin cycle.
Step 1
Locate the filter door on the bottom left of the washer.
Step 2
Open the filter door by flipping it.
Step 3
Take out the drain hose and place it in a pan or bucket.
Step 4
Remove the drain hose plug and let the water flow into the bucket.
Step 5
Unscrew and detach the drain filter cover.
Step 6
Remove any debris or blockages from the filter.
Step 7
Reattach the filter cover and screw it securely in place. Also, replace the cap on the hose.
FAQ
1. Why does my LG washer stop at the rinse spin cycle?
The most common reason for an LG washer to stop at the rinse spin cycle is a problem with the drain pump or the drain hose. Check if the drain pump is clogged or if the drain hose is kinked or blocked. Clean the drain pump filter and remove any obstructions. If the problem persists, it could be a malfunctioning pressure switch or motor control board.
2. How can I check if the drain pump is clogged?
To check if the drain pump is clogged in an LG washer, first, unplug the machine and remove the bottom front panel. Locate the drain pump and detach the hoses. Check for any debris or foreign objects that may be obstructing the pump. Clean the pump and hoses thoroughly. If the pump appears to be damaged or not working properly, it may need to be replaced.
3. What should I do if the drain hose is blocked?
If the drain hose is blocked in an LG washer, start by unplugging the machine and removing the drain hose from the back of the washer. Use a long brush or a pipe cleaner to remove any accumulated lint or debris from the hose. If the blockage is severe, you may need to replace the drain hose entirely. Ensure that the drain hose is properly connected and not kinked when reinstalling it.
4. How do I clean the drain pump filter?
To clean the drain pump filter in an LG washer, locate the filter access panel usually located at the bottom front of the machine. Open the panel and place a towel or a shallow container underneath to catch any water that may spill out. Slowly unscrew the filter cap and allow any excess water to drain. Remove any debris or lint from the filter and clean it thoroughly. Screw the cap back on and close the access panel.
5. What could be causing a malfunctioning pressure switch?
A malfunctioning pressure switch in an LG washer may be caused by a clog or blockage in the air dome or air hose. The pressure switch monitors the water level in the machine and if it detects an incorrect level, it can cause the washer to stop. Check the air dome and air hose for any obstructions and clean them if necessary. If the pressure switch is faulty, it may need to be replaced.
6. How can I determine if the motor control board is faulty?
To determine if the motor control board is faulty in an LG washer, start by checking if there are any error codes displayed on the control panel. If there are no error codes, but the washer still stops at the rinse spin cycle, it could indicate a problem with the motor control board. Consult the manufacturer’s manual for instructions on how to run a diagnostic test on the control board. If the test confirms a malfunction, the board may need to be replaced.
7. When should I call a professional for repair?
If you have followed all the troubleshooting steps and your LG washer still stops at the rinse spin cycle, it may be time to call a professional for repair. A trained technician will have the expertise and tools to diagnose and fix the problem accurately. Additionally, attempting complex repairs without proper knowledge can lead to further damage or personal injury. It is always best to seek professional assistance when unsure or if the issue persists despite your efforts.