Quck answer
To remove an icemaker from a Kenmore refrigerator, follow these steps:
1. Unplug the refrigerator and locate the water supply valve. Turn it off to prevent water leakage.
2. Open the freezer door and locate the icemaker assembly. It is usually attached to the side wall or the ceiling of the freezer.
3. Remove any screws or clips holding the icemaker in place. Carefully disconnect the electrical wiring harness from the icemaker.
4. Gently pull the icemaker assembly out of the freezer. Be careful not to damage any surrounding parts or wiring.
5. Your icemaker is now removed and can be replaced or serviced if needed.
Remember to consult your Kenmore refrigerator’s manual for specific instructions or contact a professional if you are unsure about the process.
The Kenmore ice maker diligently and quietly makes ice around the clock, or at least it should. If it starts making loud noises or not working properly, it’s time to investigate and make sure everything is okay with the Kenmore ice maker.
Removing the ice maker can make more room in the freezer, but having a functioning ice maker in the Kenmore kitchen appliance has many advantages. Replacing the ice maker is relatively easy.
Operation of the Ice Machine
A Kenmore ice maker takes water from the main water supply in the house and freezes it in a small machine located in the door or freezer compartment.
A Kenmore ice maker is durable, but it can have problems over time or not work correctly if it’s not maintained regularly. If the Kenmore Elite ice maker is not filling with water, producing less ice, making bad-tasting ice cubes, or is no longer required, it can be removed without affecting the refrigerator’s operation.
Removing the Ice Maker
Before you start taking out the ice maker from the refrigerator, unplug it. Since you’ll be working with water lines and screwdrivers, it’s safer to work on an appliance that’s not powered. Open the Kenmore freezer compartment and take out the ice bucket and chiller shelf below it.
The mounting bracket should be visible now. Use a Phillips head screwdriver or a hex head tool to loosen the screws. Don’t remove the mounting bracket and screws yet, according to RR Appliance Services.
Slide the ice maker body upwards until the mounting screws fall into the wider area of the mounting tab and are loose. Lower the ice maker gently to remove it from the tabs. You should now be able to access the rear of the freezer compartment and unplug the ice maker cords from the refrigerator to remove the ice maker from the Kenmore refrigerator.
Replacing a Kenmore Ice Machine
For a side-by-side Kenmore refrigerator, you may need to work underneath the ice maker to remove it from its cradle inside the appliance. In the right rear corner, remove the screw beneath the ice maker. Remove the plastic cover and push in the tab that is located to the left of the ice maker.
Release the locking tab on the wire harness plug with a slot screwdriver, according to Sears Parts Direct. Remove the ice maker from the rails to get to the wire harness and remove it from the plug. This will release the ice maker from the refrigerator.
Installing the New Ice Maker
To install the ice maker in the Kenmore fridge, attach the mounting plate to the new machine. Align the screw holes on the bottom of the mounting plate and slip them in, twisting until they are tight. Hold the ice maker close to the mounting rails and snap the harness into place.
Line up the new ice maker with the mounting rails and push it onto the rails so that the fill tube is in the fill cup. Slide the ice maker module until it locks into place.
FAQ
1. How do I disconnect the water supply to remove the icemaker from my Kenmore refrigerator?
To disconnect the water supply and remove the icemaker from your Kenmore refrigerator, start by locating the water shut-off valve. This valve is usually located behind the refrigerator or under the sink. Turn the valve clockwise to shut off the water supply. Next, unplug the refrigerator from the power source to ensure safety. Now, locate the water supply line that connects the icemaker to the valve. Use an adjustable wrench to loosen the compression nut and disconnect the line from the valve. Finally, remove any screws or brackets that secure the icemaker to the refrigerator, and gently lift it out of the compartment.
2. Can I remove the icemaker from my Kenmore refrigerator without disconnecting the water supply?
Yes, it is possible to remove the icemaker from your Kenmore refrigerator without disconnecting the water supply. However, it is important to note that if the water supply is not disconnected, water may continue to flow into the icemaker while it is being removed. This can lead to water leakage and potential damage to your refrigerator. If you choose to remove the icemaker without disconnecting the water supply, be sure to have a towel or container ready to catch any water that may spill out. Additionally, exercise caution and work slowly to minimize the risk of water damage.
3. How do I reinstall the icemaker in my Kenmore refrigerator after removing it?
To reinstall the icemaker in your Kenmore refrigerator after removing it, start by positioning it in the icemaker compartment. Make sure the electrical harness is properly connected to the refrigerator. Next, secure the icemaker in place using the screws or brackets that were removed during the removal process. Once the icemaker is securely in place, reconnect the water supply line to the valve. Use an adjustable wrench to tighten the compression nut and ensure a secure connection. Finally, turn on the water supply by turning the shut-off valve counterclockwise. Plug the refrigerator back into the power source, and your icemaker should be ready to use again.