Quck answer
To reprogram a Genie Intellicode, follow these steps:
1. Locate the “Learn” button on the Intellicode receiver, usually found on the motor unit of the garage door opener.
2. Press and release the “Learn” button. The LED light on the receiver will start flashing.
3. Within 30 seconds, press the button on the remote control that you want to program. The LED light on the receiver will stop flashing and stay lit, indicating successful programming.
4. Test the remote control by pressing the programmed button to operate the garage door opener.
Note: If you have multiple remotes to program, repeat steps 3 and 4 for each remote.
Genie’s Intellicode system provides enhanced security for your home by using a new code each time you open your garage door. However, if you lose your remote or need to revoke access for someone else, you must reprogram the system. Follow these steps to recode your Genie Intellicode system.
Step 1: Locate the Programming Button on the Motor Head
The programming button, also known as the Learn Code button, is located on the back of the motor head. Look for a small black button and an indicator light above the 6-inch floppy black antennae wire.
Note: If your motor head does not have an antenna, you will need to remove the cover to access the programming button and indicator light.
Step 2: Erase the Remote’s Programming
You do not need the actual remote to erase its programming. Press and hold the programming button until the indicator light stops blinking. This deactivates the remote.
Step 3: Program Your Remote
First, confirm that your remote is compatible by pressing its button. If the indicator light blinks red, the remote is compatible but not yet programmed. Press the programming button on the motor head once, then press the remote’s button three times from at least 2 feet away. The indicator light will turn from flashing to solid after the first press, go out after the second press, and the motor will run after the third press. Your remote is now programmed.
Step 4: Reset and Recode Your Intellicode Keypad
To reset the Intellicode keypad, open its cover halfway, then press and hold the program and “8” buttons at the same time while opening the cover completely. The indicator light will blink once and go out. Close the cover to complete the reset.
If you want to reprogram your keypad, first open the cover until it latches. Then, press “3,” “5,” and “7” at the same time, followed by the program button. When the red light blinks, enter your personal identification number (PIN) and press the program button again. Close the cover completely and press the programming button on the motor head. The radio signal indicator will blink red for 30 seconds. During this time, return to your keypad, enter your PIN, and press “Send” twice. Once it is complete, press “Send” one more time to test your system and move the door.
To reset or reprogram a Model GWKP Intellicode Keypad, follow the instructions below. To erase your old PIN, hold down the program, 6, and Up/Down arrow buttons in order until the red light blinks and stops. To reset the keypad, hold down the program, “6,” and Up/Down arrow buttons until the red LED blinks once and stops. Then, to reprogram, press “3,” “5,” “7,” and the program button in order. Enter your new PIN and press the program button again. Finally, press and release the programming button on the motor head and enter your PIN on the keypad.
For a Model GK-BX Intellicode Keypad, resetting requires entering the current PIN and pressing the program button twice. To reprogram, hold down the program and Up/Down arrow keys until the light flashes twice, then press “3,” “5,” “7,” and the program button in order. Enter your new PIN and press the program button again. Finally, press and release the programming button on the motor head and use the Up/Down arrow key on the keypad until the door moves.
If you want to reprogram your Intellicode 2, you need to press and hold down the program key and the Up/Down arrow key until the light flashes twice and then stops. After that, press the “3” button, then “5,” then “7” and finally the program button in the order indicated. Enter your PIN, which can be three to eight characters long, and press the program button. Hold the square programming button until the round and cylinder lights turn blue, then release it. During the next 30 seconds, enter your new code on your keypad and press and release the Up/Down arrow key several times until the door starts moving.
To reset the Intellicode 3 keypad, you need to enter the current PIN and press the program key. Repeat this step once and wait for the backlight to turn off. This means you have created a new PIN.
To reprogram the Intellicode 3, follow the same steps as for the Intellicode 2, but with a few differences. After entering your PIN, hold the square programming button until the round and cylinder lights turn blue, then release it. Press the square programming button again and release it. The lights should blink purple. On your keypad, enter your PIN and press the Up/Down arrow key three or four times until the door starts moving. Wait for 30 seconds for the light on the keypad to turn off.
FAQ
1. What is a Genie Intellicode?
A Genie Intellicode is a type of garage door opener that uses rolling code technology to enhance security. Unlike traditional garage door openers, which use a fixed code that can be easily intercepted, the Genie Intellicode generates a new code every time the opener is used. This makes it much more difficult for potential intruders to gain access to your garage.
2. Why would I need to reprogram a Genie Intellicode?
There are several reasons why you might need to reprogram a Genie Intellicode. For example, if you lose a remote control or if you suspect that someone may have gained unauthorized access to your garage, it is important to reprogram the opener to ensure the security of your home. Additionally, if you are moving to a new house, it is recommended to reprogram the Genie Intellicode to prevent any previous owners from accessing your garage.
3. How do I reset a Genie Intellicode?
To reset a Genie Intellicode, you will need to locate the “Learn Code” button on the opener. Press and release this button, and then press and hold the button on your remote control that you want to program. After a few seconds, the opener’s lights will flash, indicating that the programming was successful. Repeat this process for each remote control you want to program. It is important to note that each remote control must be programmed within 30 seconds of pressing the “Learn Code” button.
4. Can I reprogram a Genie Intellicode without a remote control?
Unfortunately, it is not possible to reprogram a Genie Intellicode without a remote control. The remote control is necessary to transmit the new code to the opener. If you have lost your remote control, you will need to purchase a new one and follow the programming instructions provided by the manufacturer. It is also recommended to erase the previous codes from the opener to ensure the security of your garage.
5. Are there any additional security measures I can take with a Genie Intellicode?
Yes, there are additional security measures you can take with a Genie Intellicode. One option is to enable the “Vacation Lock” feature, which disables all remote controls and keypad entry until you manually reactivate them. This can be useful when you are away from home for an extended period of time. Additionally, it is important to regularly change the access code on your remote controls and keypad to further enhance security.