Quck answer
To change the light bulb in a Sharp Carousel Microwave, follow these steps:
1. Unplug the microwave and wait for it to cool down.
2. Locate the bulb cover inside the microwave. It is usually located on the side or back of the cavity.
3. Remove the screws or clips holding the bulb cover in place.
4. Take out the old bulb and replace it with a new one of the same wattage and type.
5. Secure the bulb cover back in place and tighten any screws or clips.
6. Plug in the microwave and test the new bulb to ensure it is working properly.
The microwave often goes unnoticed for its daily usage in the kitchen. Whether it’s reheating a cup of coffee or turning cold leftovers into a hot lunch, this small appliance does its job diligently and requires minimal maintenance. However, when the light inside the microwave stops working, it can become an inconvenience.
If the Sharp carousel microwave’s light fails to turn on when the door is opened, it may need to be replaced. Replacing the lightbulb in a Sharp carousel microwave is an easy task that can be accomplished with minimal effort.
Precautions before Replacing the Microwave Bulb
Using the microwave with a burnt-out lightbulb is safe, but it can be bothersome. When the door is closed, the shaded glass makes it difficult to see if the cheese is melted to your liking or the hot dogs are cooked. Do not be intimidated by changing the burnt-out bulb, but be cautious when working with electrical appliances. It is recommended to unplug the unit from the electrical outlet before replacing the bulb, according to GE Appliances.
If you have a built-in microwave, look for a plug above, below, or on the side of the unit. The electrical cord may run through a hole in the cabinet to an outlet located close to the appliance. If the microwave is new and the lightbulb is not working, Sharp states that the limited warranty will cover the replacement done by a professional. However, some warranties may be voided if you open the microwave cabinet yourself.
Sharp carousel microwave oven lightbulbs can be purchased at most big box home improvement stores or online. Consult the owner’s manual for your specific model to ensure you are purchasing the correct bulb. You can also check the reference number on the old bulb.
Replacing the Sharp Microwave Lightbulb
After unplugging the appliance and obtaining the correct bulb, replacing the Sharp microwave lightbulb should take only a few minutes. You will need a Phillips screwdriver and a bowl to hold the screws and lightbulb cover plate. Some microwaves will not function if the light cover is not properly secured in its nook.
Remove the screws from the back of the microwave and locate the cover to the light box. Remove the screws from the top and sides of the cover. Gently pull out the lightbulb and use a potato or thick sponge to twist the glass bulb safely from its housing if it is broken. Push the potato or thick sponge over the broken glass until it meets the metal of the bottom of the bulb. Slowly twist until the bulb releases from the connection.
Twist the new bulb into place and replace the light cover. Tighten the screws to prevent them from shaking loose and falling into the microwave cabinet. This is a good opportunity to clean the inside of the microwave and the removed back cover with a dry, soft cloth. Replace the back of the microwave cabinet and screw it into place.
FAQ
1. How do I know when the light bulb in my Sharp Carousel Microwave needs to be replaced?
You will know that it is time to replace the light bulb in your Sharp Carousel Microwave when the interior light no longer comes on when you open the microwave door. If the bulb appears to be burnt out or if you notice that it flickers or dims, it is also a good indication that it needs to be replaced.
2. What type of light bulb should I use to replace the one in my Sharp Carousel Microwave?
To replace the light bulb in your Sharp Carousel Microwave, you will need to use a 20-watt halogen bulb. It is important to use the correct wattage bulb to ensure that it is compatible with your microwave and to prevent any potential damage.
3. How do I change the light bulb in my Sharp Carousel Microwave?
To change the light bulb in your Sharp Carousel Microwave, you will need to follow these steps:
1. Unplug the microwave from the power source for safety purposes.
2. Locate the light bulb cover on the microwave’s interior. It is usually located at the top or back of the microwave.
3. Remove the screw or clips holding the cover in place and carefully remove the cover.
4. Gently remove the old light bulb from its socket and replace it with the new 20-watt halogen bulb.
5. Place the light bulb cover back in its original position and secure it with the screw or clips.
6. Plug the microwave back into the power source and test the new light bulb by opening the microwave door.