Quck answer
To remove the drum from a Whirlpool washing machine, follow these steps:
1. Turn off the power and unplug the machine.
2. Open the machine’s door and remove any clothes or items inside.
3. Remove the detergent dispenser drawer if applicable.
4. Locate and remove any screws or bolts holding the top panel in place.
5. Lift the top panel and set it aside.
6. Remove any screws or bolts securing the control panel and disconnect any wiring harnesses.
7. Remove the front panel by unscrewing any screws or releasing any clips.
8. Locate and remove any screws or bolts holding the drum in place.
9. Carefully lift and remove the drum from the machine.
Remember to consult the manufacturer’s manual for specific instructions and safety guidelines.
Periodically, it is necessary to clean and maintain the drum inside your Whirlpool washing machine, as lint, fabrics or clothing pieces could get stuck behind its mechanism. If there’s no cleanup or maintenance, the performance of a top-loading washing machine drum can be hampered.
How to Remove the Drum from a Whirlpool Washing Machine
If you have mechanical skills to handle appliances, you can easily undertake Whirlpool washer drum removal and save on cost because some professionals might charge sky-high prices for such repairs.
What to Prepare
Before doing any work, make sure that the washing machine is off and unplugged to prevent electrical shock. Turn off the water supply and disconnect the water tubes from the machine.
If possible, move the unit away from the wall to have more space to work. Tape the lid of the machine tightly so it won’t open once you pull parts off. You may need to use a spanner wrench, hammer, flat screwdriver, socket set, and ratchet for this undertaking. Wear gloves while you work to protect your hands.
Removing a Washing Machine Drum
The drum of a basic top-loading washing machine has two tubs inside. The inner tub is the washer basket, while the outer tub is the actual drum. The back of the machine holds and supports part of this drum, so carefully unscrew the bolts from the backside to lift the top panel.
Once the top panel is gone, you’ll see some clips that connect the inner and outer tubs together. Use a flat screwdriver to unhook these clips, which should loosen the top ring holding the washer basket’s locking tabs.
Next, remove the impeller located in the bottom center, which helps the tub spin. It’s likely covered with a plastic cap. When you take the cap off, use a bolt remover to unscrew and loosen the impeller. Some machines might have an agitator instead of an impeller. Agitators are longer and have obvious spindles.
With the impeller or agitator off, take out the spanner nut using a wrench and hammer and then carefully pull the basket off the tub. You can now clean the basket and remove any objects stuck in the drum.
Putting the Drum Back Together
Position the washer basket appropriately on its shaft before tightening the spanner nut. Put the impeller back in its slot and reapply a Threadlocker Blue 242 adhesive, according to Whirlpool, to prevent it from spinning the washer basket out of place.
Place the tub ring after the impeller has been secured and then lock these down with the clips. Finally, lower the top panel and tighten all the areas that have screws.
These tips might also work on a Maytag or Kenmore washer spin basket or a Samsung top-load washer disassembly since these machines operate the same way and have a similar system.
FAQ
1. How do I remove the drum from a Whirlpool washing machine?
To remove the drum from a Whirlpool washing machine, you will need to follow these steps:
1. Unplug the washing machine and turn off the water supply.
2. Remove the detergent dispenser by pulling it out.
3. Take off the control panel by removing the screws or clips that hold it in place.
4. Disconnect the wires connected to the control panel.
5. Remove the top panel by lifting it up.
6. Undo the screws that hold the front panel in place and remove it.
7. Locate the drum and remove the bolts or screws that secure it to the machine.
8. Carefully lift the drum out of the washing machine.
Remember to always refer to the manufacturer’s instructions or consult a professional if you are unsure about any step.
2. Can I remove the drum from my Whirlpool washing machine by myself?
Yes, you can remove the drum from your Whirlpool washing machine by yourself if you have the necessary tools and knowledge. However, it is recommended to have some experience in appliance repair before attempting this task. Removing the drum involves disassembling various parts of the washing machine, and it can be a complex process. If you are unsure or uncomfortable with DIY repairs, it is best to hire a professional technician to perform the task for you. They have the expertise and tools required to safely and efficiently remove the drum without causing any damage to the machine.
3. Why would I need to remove the drum from my Whirlpool washing machine?
There are a few reasons why you might need to remove the drum from your Whirlpool washing machine:
1. Repair or replace a faulty drum: If the drum is damaged or not functioning properly, you may need to remove it to repair or replace it with a new one.
2. Remove a stuck item: Sometimes, small items like socks or underwear can get stuck between the drum and the tub. Removing the drum allows you to access and retrieve these items.
3. Clean the drum and tub: Over time, dirt, lint, and detergent residue can build up inside the drum and tub. Removing the drum makes it easier to clean these parts thoroughly.
Remember to always follow proper safety precautions and consult the manufacturer’s instructions or a professional technician when working on your washing machine.