Quck answer
To light the gas pilot light on a Wedgewood by Atwood stove, follow these steps:
1. Locate the pilot light assembly, usually at the bottom of the stove near the burner.
2. Turn the gas control knob to the “Off” position.
3. Wait for a few minutes to allow any residual gas to dissipate.
4. Turn the gas control knob to the “Pilot” position.
5. Hold a lit match or lighter near the pilot light assembly.
6. Press and hold the gas control knob while continuing to hold the match or lighter near the pilot light assembly.
7. Once the pilot light is lit, continue holding the gas control knob for about 30 seconds to ensure the pilot light stays lit.
8. Release the gas control knob and turn it to the desired temperature setting.
9. If the pilot light goes out, repeat steps 4-8.
Remember to always follow the manufacturer’s instructions and exercise caution when working with gas appliances.
It is important to know how to light the pilot on a Wedgewood stove by Atwood. These ovens are commonly found in boats and RVs, and require manual ignition of the pilot light whenever the gas supply is interrupted. The pilot light is located on the right-hand side of the stove burner, beneath the broiler pan. Proper positioning of the stove knobs is necessary for successful ignition.
Step 1
Turn the gas valve on the stove to the “On” position.
Step 2
Rotate the knob on the far right-hand side of the Wedgewood oven counterclockwise until it reads “Pilot On–Push/Hold.”
Step 3
Locate the oven pilot beneath the broiler on the right-hand side of the stove.
Step 4
Light a match. While holding the “Pilot On–Push/Hold” knob on the far-right of the Wedgewood stove, place the lit match directly beneath the oven pilot. Once the pilot ignites, continue holding the knob for five seconds. Release the knob and verify that the pilot remains lit.
Step 5
Turn the knob on the far right of the oven to “Pilot Push/Hold.” The oven and broiler are now ready for use.
FAQ
1. How do I locate the gas pilot light on a Wedgewood by Atwood stove?
To locate the gas pilot light on a Wedgewood by Atwood stove, you need to open the stove’s top cover. Look for a small metal plate or panel at the bottom of the stove’s interior. The pilot light should be located near this area.
2. What equipment do I need to light the gas pilot light?
To light the gas pilot light on a Wedgewood by Atwood stove, you will need a long-reach lighter or a long match. This is necessary as the pilot light is often located deep inside the stove and cannot be reached with a regular lighter or match.
3. How do I safely light the gas pilot light on a Wedgewood by Atwood stove?
To safely light the gas pilot light, make sure the stove’s control knob is in the “Off” position. Then, turn the control knob to the “Pilot” position and press it down. While holding the control knob down, use the long-reach lighter or match to ignite the pilot light. Once the pilot light is lit, continue to hold the control knob down for about 30 seconds to allow the thermocouple to heat up. Finally, release the control knob and the pilot light should stay lit.
4. What should I do if the gas pilot light does not stay lit?
If the gas pilot light does not stay lit, it may be due to a dirty or clogged pilot assembly. In this case, turn off the gas supply to the stove and wait for it to cool down. Once cooled, use a small brush or compressed air to clean the pilot assembly. If the issue persists, it is recommended to contact a professional technician for further assistance.
5. Can I light the gas pilot light on a Wedgewood by Atwood stove without a long-reach lighter or match?
No, it is not recommended to attempt lighting the gas pilot light without a long-reach lighter or match. The pilot light is often located deep inside the stove and cannot be reached with a regular lighter or match. Using improper tools or methods may result in injury or damage to the stove. It is always best to use the appropriate equipment for the task at hand.