Quck answer
To light a Roper oven pilot light, follow these steps:
1. Locate the oven pilot light: It is usually located at the bottom of the oven, near the burner.
2. Turn off the oven: Make sure the oven is turned off before attempting to light the pilot light.
3. Remove the oven bottom: Remove the oven bottom to access the pilot light.
4. Find the pilot light valve: Locate the pilot light valve, which is usually located near the burner.
5. Turn the pilot light valve to “pilot”: Turn the valve to the “pilot” position.
6. Light the pilot light: Use a long lighter or match to ignite the pilot light while holding down the valve.
7. Hold for a few seconds: Keep holding the valve down for a few seconds to allow the pilot light to stay lit.
8. Release the valve: Release the valve once the pilot light stays lit.
9. Replace the oven bottom: Put the oven bottom back in place.
10. Test the oven: Turn on the oven and check if it works properly.
Remember to always refer to the manufacturer’s instructions for specific details on lighting your Roper oven pilot light.
Although modern technology has made life easier, some people still prefer antique items like Roper ovens and stoves. Even though Roper ovens are no longer manufactured, those who own them may need help with Roper electric stove troubleshooting. One common issue is lighting the Roper gas stove or Roper oven range pilots.
Lifting the Cooktop
Before lighting the Roper gas stove or Roper oven range pilots, turn off all controls. Then, remove the surface burner grates and lift the cooktop. According to the Roper Home Appliances Use and Care Guide, lift the front of the cooktop at both front corners until the support rods lock into place.
Lighting the Roper Stove Pilot Light
Hold a match over the pilot light located between the front and back burners. Ensure the pilot flame is only 1/4 inch to 3/8 inch high. Adjust the pilot light by turning the pilot adjustment screw midway down the length of the manifold pipe, behind the control panel. After lighting the range pilots, lower the cooktop and replace the grates.
Lighting the Roper Oven Burner Pilot
Turn off the oven temperature control, then remove the oven bottom by removing the two hold-down screws located at the rear of the Roper oven. If the screws are tight, use a screwdriver. Lift the rear of the panel up and back until the lip of the front of the panel is clear of the front frame of the Roper oven cavity. Unscrew the burner baffle located on the burner, then hold a lit match over the Roper oven burner pilot located at the rear of the burner. Check the burner lighting by turning the oven temperature control to a temperature above 140 degrees Fahrenheit. Replace the burner baffle and the oven bottom after the burner pilot burns steadily.
FAQ
1. What is a pilot light in a Roper oven?
A pilot light is a small flame that is constantly burning in a Roper oven. It is used to ignite the main burner and ensure that the oven stays lit. The pilot light is usually located near the bottom of the oven and is visible through a small window or opening.
2. Why would I need to light the pilot light in my Roper oven?
You may need to light the pilot light in your Roper oven if it has gone out. This can happen if there is a power outage, if the gas supply is interrupted, or if the pilot light is simply not functioning properly. Lighting the pilot light is necessary to ensure that the oven can be used for cooking.
3. How do I locate the pilot light in my Roper oven?
The location of the pilot light can vary slightly depending on the model of your Roper oven. However, in most cases, you can find the pilot light by opening the oven door and looking near the bottom of the oven, towards the back. There should be a small access panel or opening that allows you to see and access the pilot light.
4. What tools or materials do I need to light the pilot light in my Roper oven?
To light the pilot light in your Roper oven, you will typically need a long lighter or a match. Additionally, it is helpful to have a flashlight on hand to better see the pilot light and any controls or knobs that may need to be manipulated.
5. What are the steps to light the pilot light in my Roper oven?
To light the pilot light in your Roper oven, follow these general steps:
1. Locate the pilot light
2. Turn the oven control knob to the “Pilot” position
3. Depress and hold the oven control knob to start the flow of gas
4. Use a long lighter or match to ignite the pilot light
5. Continue holding the oven control knob for about 30 seconds to allow the pilot light to heat up
6. Release the oven control knob and the pilot light should stay lit
7. Turn the oven control knob to the desired temperature to start using the oven
6. What should I do if the pilot light in my Roper oven won’t stay lit?
If the pilot light in your Roper oven won’t stay lit, there may be an issue with the thermocouple. The thermocouple is a safety device that detects whether the pilot light is lit or not. If it is faulty, it may not register the presence of the pilot light and will shut off the gas flow. In this case, it is recommended to contact a professional technician to inspect and replace the thermocouple if necessary.
7. Are there any safety precautions I should take when lighting the pilot light in my Roper oven?
Yes, there are a few safety precautions to keep in mind when lighting the pilot light in your Roper oven. Make sure the area around the oven is well-ventilated to prevent the buildup of gas. Avoid using flammable materials or wearing loose clothing that could come into contact with the flame. If you smell gas or suspect a gas leak, turn off the gas supply immediately and contact a professional technician for assistance.